Goal Zero Yeti 300 runtimes

Every load we have calculated for the Goal Zero Yeti 300.

Each answer below runs the same checks in the same order: voltage first, then continuous output, then startup demand, and only then stored energy. Where a figure is missing from the published evidence, the page says so rather than assuming it clears.

Refrigeration

Refrigeration loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

Not a matchRunning a household refrigeratorThe 1,200W start exceeds the published 600W peak, so the station is likely to shut down on the first compressor or motor start.Open this guide

Running a chest freezerThe 900W start exceeds the published 600W peak, so the station is likely to shut down on the first compressor or motor start.Not a match Running an upright freezerThe 1,000W start exceeds the published 600W peak, so the station is likely to shut down on the first compressor or motor start.Not a match Running a mini fridgeAbout 11 hr on our planning profile, before any reserve is held back.11 hr Running a 12V portable fridgeAbout 14 hr on our planning profile, before any reserve is held back.14 hr

Communications

Communications loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

7.1 hrRunning a Starlink MiniAbout 7.1 hr on our planning profile, before any reserve is held back.Open this guide

Running a router and modemAbout 13 hr on our planning profile, before any reserve is held back.13 hr

Work and electronics

Work and electronics loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

5.9 hrRunning a laptopAbout 5.9 hr on our planning profile, before any reserve is held back.Open this guide

Running a televisionAbout 2.8 hr on our planning profile, before any reserve is held back.2.8 hr

Medical

Medical loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

6.7 hrRunning a CPAP machineAbout 6.7 hr on our planning profile, before any reserve is held back.Open this guide

Water management

Water management loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

Not a matchRunning a sump pumpA 630W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Open this guide

Running a well pumpA well pump needs 240V. The Goal Zero Yeti 300 supplies 115V only, so it cannot power this appliance at all.Not a match

Heating

Heating loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

Not a matchRunning a gas furnace blowerA 600W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Open this guide

Running a pellet stoveAbout 1.9 hr on our planning profile, before any reserve is held back.1.9 hr Running an electric space heaterA 1500W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Not a match Running an electric blanketAbout 6.2 hr on our planning profile, before any reserve is held back.6.2 hr

Cooling

Cooling loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

Not a matchRunning a window air conditionerA 500W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Open this guide

Running a dehumidifierA 480W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Not a match Running a box fanAbout 3.9 hr on our planning profile, before any reserve is held back.3.9 hr

Kitchen

Kitchen loads calculated against the 296.96Wh capacity and 350W continuous output of this station.

Not a matchRunning a microwave ovenA 1400W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Open this guide

Running a drip coffee makerA 900W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Not a match Running an electric kettleA 1500W running load exceeds the 350W continuous rating, so the station cannot sustain this appliance.Not a match

A runtime figure is the end of the check, not the start of it.

Voltage, continuous output, and startup demand all have to clear before stored energy decides anything. Measure your own appliance before treating any of these numbers as a purchase decision.

Read the calculation and evidence methodology