Skip to main content
Power Station StationIndependent power planning
Menu

Runtime calculation

How Long Will an Anker SOLIX F3800 Run a Well Pump

This estimate separates electrical compatibility from battery endurance. Published specifications control where they exist, and every planning default is labelled where the manufacturer leaves a gap.

Research by the Power Station Station Editorial Team

Estimated runtime
41 hours
From 3,840Wh rated capacity against a 75W average load.
Continuous output
6,000 W
What the inverter can sustain. Output decides whether the appliance runs at all.
Published peak
9,000 W
Manufacturer surge figure, used only for the startup check.

Our answer

On our planning profile the Anker SOLIX F3800 runs a well pump for about 41 hours, or 32 hours if you keep a reserve back.

The checks behind this answer

Stored energy is the final check, not the first. Voltage, continuous output, and startup demand must clear before runtime means anything. Missing published evidence stays marked unverified instead of being treated as a pass.

Electrical checks applied to this station and appliance pairing
CheckResultWhy
VoltageClearsA well pump needs 240V, and this station provides a 240V output.
Continuous outputClearsA 1500W running load sits inside the 6,000W continuous rating, leaving about 300% headroom.
Startup demandClearsThe 4,500W start is covered by continuous output alone, so no surge rating is needed.

How the number is built

A battery holds back some of its rated capacity, and converting to household AC costs more on top. Of the 3,840Wh rated here, roughly 3,041Wh reaches the outlet under a conservative planning model.

That energy meets an average load of 75W, which applies a 5% duty cycle to a 1500W running draw. Holding back a 20% reserve for battery age, cold, and a longer outage leaves 32 hours. These are calculations, not measurements from a test.

Before you rely on this

These limits decide whether this appliance belongs on a portable battery at all.

  • Most residential well pumps are hardwired. Connecting one to a portable station is electrical work, not a plug-in task, and a transfer switch installed by a licensed electrician is the lawful way to do it.
  • A portable station that cannot supply 240V cannot run a 240V pump, regardless of its stored energy.
  • Nothing on this page is a substitute for an electrician's assessment of your own installation.

Replace our assumptions with your own

Whether your pump has a soft start changes the answer completely. A soft-start submersible may be within reach of a large portable station; a conventional 240V pump generally is not.

Find the pump nameplate, usually inside the pressure-switch cover or on the original paperwork, and record voltage, horsepower, and rated amps. A licensed electrician can measure actual starting current safely.

Continue through this cluster

Use the next page that answers your unresolved constraint

Everything a Anker SOLIX F3800 can runCompare this answer against the other loads the same station covers.Well pump power requirementsWork through the load itself before choosing hardware for it.Anker SOLIX F3800 specifications and sourcesSee where every number on this page came from.All Anker SOLIX recordsCompare the rest of the range.Runtime calculatorReplace our planning defaults with your own measurements.

Evidence used on this page

Important fields are tied to a specific source. Manufacturer claims, government guidance, calculations, and planning assumptions remain separate.

  1. Published specification table plus the comparison chart and FAQ for the banded solar input current.

    official product page

  2. Documents model-dependent 100 to 115V and 200 to 240V supplies, soft start, and generator sizing guidance.

    official manual

  3. Wiring design and protection, 29 CFR 1910.304

    Occupational Safety and Health Administration

    Safety context for branch circuits, overcurrent protection, and grounding. A portable station must not be improvised into home wiring.

    government guidance

  4. Defines the capacity, efficiency, reserve, duty-cycle, voltage, continuous-output, and startup checks applied across the site. Planning defaults are visible on every page that uses them.

    planning assumption

  5. Tech specs table for outlets, USB, solar and AC input; the F3800 Plus comparison table for the XT-60 solar connector, the two DC input ports and the firmware-dependent solar current bands; FAQ Q1 for the same bands stated in prose.

    official product page

  6. Anker's own comparison tool. Source for AC outlet counts, per-port USB wattage, car auxiliary rating, AC input and the MPPT current limit. Its receptacle type labels are not used: it prints "NEMA 6-20" for outlets it annotates as 120V.

    official product page