Skip to main content
Power Station StationIndependent power planning
Menu

Runtime calculation

How Long Will a Goal Zero Yeti PRO 4000 Run a Sump Pump

This estimate separates electrical compatibility from battery endurance. Published specifications control where they exist, and every planning default is labelled where the manufacturer leaves a gap.

Research by the Power Station Station Editorial Team

Estimated runtime
50 hours
From 3,993.6Wh rated capacity against a 63W average load.
Continuous output
3,600 W
What the inverter can sustain. Output decides whether the appliance runs at all.
Published peak
7,200 W
Manufacturer surge figure, used only for the startup check.

Our answer

On our planning profile the Goal Zero Yeti PRO 4000 runs a sump pump for about 50 hours, or 40 hours if you keep a reserve back.

The checks behind this answer

Stored energy is the final check, not the first. Voltage, continuous output, and startup demand must clear before runtime means anything. Missing published evidence stays marked unverified instead of being treated as a pass.

Electrical checks applied to this station and appliance pairing
CheckResultWhy
VoltageClearsA sump pump runs on 115V and the Goal Zero Yeti PRO 4000 supplies 120V AC.
Continuous outputClearsA 630W running load sits inside the 3,600W continuous rating, leaving about 471% headroom.
Startup demandClearsThe 1,800W start is covered by continuous output alone, so no surge rating is needed.

How the number is built

A battery holds back some of its rated capacity, and converting to household AC costs more on top. Of the 3,993.6Wh rated here, roughly 3,163Wh reaches the outlet under a conservative planning model.

That energy meets an average load of 63W, which applies a 10% duty cycle to a 630W running draw. Holding back a 20% reserve for battery age, cold, and a longer outage leaves 40 hours. These are calculations, not measurements from a test.

Before you rely on this

These limits decide whether this appliance belongs on a portable battery at all.

  • A portable power station is not a substitute for a permanently installed sump-pump battery backup system, and nothing here is a guarantee against flooding.
  • Startup current is the usual failure point. A station with enough stored energy can still shut down on the first motor start.
  • Do not improvise a portable station into house wiring. Plug the pump directly into the station.

Replace our assumptions with your own

The duty cycle is the whole question. Rainfall, water table, and pit size decide how often the pump runs, and a planning figure cannot know any of them for your basement.

Read the nameplate amps, then count actual pump cycles during a heavy rain event and time one cycle. That gives you a duty cycle grounded in your own basement.

Continue through this cluster

Use the next page that answers your unresolved constraint

Everything a Goal Zero Yeti PRO 4000 can runCompare this answer against the other loads the same station covers.Sump pump power requirementsWork through the load itself before choosing hardware for it.Goal Zero Yeti PRO 4000 specifications and sourcesSee where every number on this page came from.All Goal Zero recordsCompare the rest of the range.Runtime calculatorReplace our planning defaults with your own measurements.

Evidence used on this page

Important fields are tied to a specific source. Manufacturer claims, government guidance, calculations, and planning assumptions remain separate.

  1. Published specification table covering capacity, chemistry, lifecycles, inverter output, both solar input channels with their voltage and current limits, weight, and warranty.

    official product page

  2. Representative 1/3 HP, 115V automatic pump rated at 5.5A. An example, not a universal sump-pump preset.

    official manual

  3. Wiring design and protection, 29 CFR 1910.304

    Occupational Safety and Health Administration

    Safety context for branch circuits, overcurrent protection, and grounding. A portable station must not be improvised into home wiring.

    government guidance

  4. Defines the capacity, efficiency, reserve, duty-cycle, voltage, continuous-output, and startup checks applied across the site. Planning defaults are visible on every page that uses them.

    planning assumption

  5. Published specification table: inverter output and waveform, every DC and USB port with its rating, the solar input window and current limit, AC charge input, and expansion.

    official product page